Frigidaire Dishwasher i10 Error
What it means
i10 means your Frigidaire dishwasher detected a low fill — not enough water entered the tub fast enough during the fill step. It usually points to a water-supply restriction, a clogged inlet screen, or a weak water inlet valve.
The bottom line on the i10 error
The i10 code is a low-fill warning, and more often than a dead pump the real culprit is a partly closed supply valve, a kinked fill hose, or a scaled-up inlet screen. Cutting power resets the code, but it comes back next cycle until the actual restriction is cleared.
Start with the free checks — open the supply, straighten the hose, and clean the inlet screen — before buying parts. Only if flow stays weak is the $30 to $60 inlet valve worth it, and since a $130 to $250 pro repair still beats a new dishwasher, repair is the clear call.
i10 snapshot
Our own at-a-glance triage of the i10 error, from the verified data on this page. See error-code rankings → · How we score →
Common causes of the i10 error
- The water supply valve under the sink is partly or fully closed.
- A kinked or crimped fill hose restricting water into the dishwasher.
- A clogged inlet screen inside the water inlet valve, choked with sediment or scale.
- A clogged or split pressure (air) hose between the sump and the level sensor, so the control misreads the fill.
- A weak or failing water inlet valve that opens but does not let enough water through.
Which Frigidaire dishwashers get the i10 error
Common on Frigidaire and Frigidaire Gallery built-in dishwashers (many FFBD, FFCD, FGID, FGIP, and FPID series) from roughly 2010 onward, plus Electrolux-built units that share the same fill-sensing control. Hard-water regions see it most because scale clogs the inlet valve screen over time.
How to fix the Frigidaire Dishwasher i10 error
- 1Check the water supplyConfirm the shutoff valve under the sink that feeds the dishwasher is fully open. Then trace the fill hose behind the unit and straighten any kinks or crimps so water can flow freely.
- 2Clean the inlet valve screenTurn off the water supply, then disconnect the fill hose from the dishwasher's water inlet valve. Inspect the small metal or plastic screen inside the valve inlet and gently clear any sediment with a soft brush. Reconnect securely and turn the water back on.
- 3Verify the fill levelStart a short cycle and open the door after 2-3 minutes. There should be water covering the bottom sump area by roughly a quarter to half an inch. If little or no water is present, the fill problem is confirmed and you should move to the valve and sensor checks.
- 4Check the pressure hose and inlet valveWith power and water off, remove the lower access panel and find the thin pressure hose running from the sump to the level sensor; make sure it is not clogged, pinched, or split. If water flow is still weak when the valve is energized during fill, the water inlet valve assembly likely needs replacing.
🧰 When to call a professional
If the supply is open, the screen is clean, and the hoses are clear but i10 keeps returning, the water inlet valve or the control board may be at fault. Testing valve voltage and replacing the valve requires working near water and electrical connections behind the panel, so call a qualified technician if you are not comfortable with that.
Frigidaire i10 vs GE C1 vs Bosch E15: how they compare
How this code stacks up against related error codes for difficulty, urgency, and cost.
How much does it cost to fix the i10 error?
| DIY fix (open valve / straighten hose) | $0 |
| DIY parts (water inlet valve) | $30–$60 |
| Professional repair (parts + labor) | $130–$250 |
Repair or replace?
Start with the free checks — a partly closed supply valve, a kinked fill hose, or a scaled-up inlet screen fixes many i10 cases for $0. If the water inlet valve has actually failed, it's a $30–$60 DIY part, or roughly $130–$250 with a technician's diagnostic and labor. Since even a professional repair stays well under the $400–$900 cost of a new dishwasher, repair is the clear choice unless the machine is 10+ years old and showing other faults, where the 50 percent rule tips toward replacement.
Common replacement parts for the i10 error
| Water inlet valve | $30–$60 | OEM valves (e.g. Frigidaire 807047901); the usual i10 culprit if flow stays weak. | |
| Fill / pressure hose | $15–$40 | Only if the hose is kinked, split, or clogged rather than the valve itself. |
Prices are typical retail ranges and vary by model and supplier — always confirm the exact part number for your appliance before buying.
Frigidaire i10 error — FAQ
＋ − Will the dishwasher still run with the i10 code?
It may start but cannot wash properly without enough water, and it will usually stop early or repeat the fault. Fix the low-fill cause before relying on it for a full cycle.
＋ − How do I reset a Frigidaire dishwasher with the i10 error?
Cut power to the dishwasher at the breaker or unplug it for a few minutes, then restore power. If the supply and inlet are fine, the reset clears the code; if the fill problem remains, i10 will come back.
＋ − Could hard water cause i10?
Yes. Mineral scale from hard water can clog the small inlet valve screen over time, slowing the fill. Cleaning the screen often restores normal flow, and periodic descaling helps prevent it from recurring.
Sources & manufacturer references
This guide is independently written and not affiliated with Frigidaire. Always unplug appliances before servicing and follow your model's manual. Error codes and steps can vary by model — when in doubt, consult a qualified technician.